Top seller
No results were found for the filter!
Description ETH Wiz click carries W5500 , a 48-pin, 10/100 BASE-TX standalone ethernet controller with a hardwired TCP/IP Internet protocol offload engine, along with a standard RJ-45 connector. The W5500 module employs a variety of...
₹1,999.00 *
Description EXPAND 2 click is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23017 with I²C clock speeds up to 10 MHz for higher throughput applications. Three HARDWARE ADDRESS SEL jumpers allow you to...
₹1,259.00 *
RS232 click is a simple solution for adding RS232 connectivity to your design. RS232 is a serial communications standard mostly used for industrial machines, networking equipment and scientific instruments, as well as for computer...
₹1,579.00 *
PS/2 click is a cost-effective solution for adding keyboard and mouse connectivity to your design. It features a standard 6-pin Mini-DIN PS/2 connector, a mikroBUS™ host socket, and a power indicator LED. PS/2 click communicates with the...
₹949.00 *
Fiber Opt click is a compact and easy solution for adding fiber-optic communication to your design. It features IF-D91 fiber-optic photodiode, IF-E97 fiber-optic LED diode as well as two operational amplifiers. Provided plastic optic...
₹3,569.00 *
FTDI Click features FT2232H - dual high speed USB 2.0 to UART/I2C/SPI serial interface converter. It includes DA converter and EEPROM as well. The entire USB protocol is handled on the chip (FTDI USB drivers are required), making this...
₹3,049.00 *
4-20mA R Click is an add-on board in mikroBUS form factor which serves as a receiver in a 4-20mA current loop standard. It features INA196 current shunt monitor, MCP3201 12-bit ADC as well as TPS61041 DC/DC boost converter. It receives...
₹2,729.00 *
DALI Click is a compact board that provides Digital Addressable Lighting Interface (DALI) to your design. Board features two optocouplers, push button and screw terminals. DALI Click communicates with target board via four mikroBUS™...
₹2,629.00 *
Description CAN SPI click 3.3V is an accessory board in mikroBUS form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features SN65HVD230 can transciever circuit which provides...
₹2,209.00 *
Description RS485 click 3.3V carries the SN65HVD12 half-duplex, RS-485 transceiver from Texas Instruments. It is designed for balanced data transmission and complies with EIA standards RS-485 and RS-422. The click is designed to run on a...
₹1,889.00 *
Description ETH Click is an accessory board in mikroBus™ form factor. It features ENC28J60 , a 28-pin, 10BASE-T stand alone Ethernet Controller with an on-board MAC & PHY, 8K Bytes of Buffer RAM and SPI serial interface. Chip supports...
₹2,519.00 *
Description EXPAND Click is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23S17 with SPI clock speeds up to 10 MHz for higher throughput applications. Three HARDWARE ADDRESS SEL jumpers allow you to...
₹1,259.00 *
MCP2003B click SPI Isolator Expand 3 click RS485 click Fiber Opt click iButton click UART 1-Wire I2C Isolator 2 GNSS 10 Click USB I2C click UART I2C SPI PICtail Plus RS485 3 click ATA6563 click I2C Isolator USB SPI click Click MCP2518FD click USB UART 2 Arduino MEGA RS485 click 5V RS485 4 Click EXPAND click FRDM K64 click LPCXpresso Pi 4 Click DALI Click 4-20 mA T click DALI 2 click Arduino MKR FTDI click LLC SPI Click OBDII click RS232 Isolator Expand 4 click RS232 2 click PS 2 click Ambient 15 ETH WIZ click 1-Wire I2C Expand 2 click MCP2517FD click I2C 1-Wire BroadR-Reach PWM 2 click RS232 click
Viewed