Top seller
No results were found for the filter!
PAC1934 click carries the PAC1934 four channel DC power/energy monitor from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over an I2C interface. How the click...
₹3,049.00 *
LEM click carries the LTS 6-NP current transducer and MCP3201 ADC converter. The click can measure AC and DC current with exceptional speed, up to 200 KHz . LEM click is designed to run on either 3.3V or 5V power supply. It communicates...
₹6,199.00 *
ADAC click is an 8-channel 12-bit ADC, DAC and GPIO. It carries the AD5593R configurable ADC/DAC. The click is designed to run on either 3.3V or 5V power supply. ADAC click communicates with the target microcontroller over I2C interface,...
₹2,729.00 *
AC Current click can measure alternating currents up to 30A and it features the MCP3201 ADC (analog to digital) converter and the MCP607 CMOS Op Amp, both from Microchip. The click is designed to run on either 3.3V or 5V power supply. It...
₹1,469.00 *
The design of the board is based on an OpAmp set up as a differential amplifier with a buffered input. Two onboard screw terminals (probe+ and probe-) are bringing in the current, which then flows through a row of four resistors. A...
₹2,519.00 *
The analog output is fed through a 12-bit ADC with the final output going through the mikroBUS™ SPI interface. Since the ADC has a limited min-max range (0-2043), R Meter click employs a multiplexer that can adjust the input signal to...
₹2,839.00 *
Two onboard screw terminals (probe+ and probe-) are bringing in the current, which then passes through a shunt resistor. A voltage proportional to the strength of the current is generated accross the resistor. This voltage passes through...
₹2,519.00 *
The chip is implemented in an astable multivibrator circuit with fixed resistors and adjustable capacitors. The board has four different-sized plates for placing SMD capacitors (covering standard SMD packaging dimensions) as well as a...
₹949.00 *
DIGI POT 2 click is a mikroBUS™ add-on board with a single channel digital potentiometer TPL0501 with 256 wiper positions. The IC has 100 kilo Ohms end-to-end resistance, with ±20% tolerance. The board features two pairs of screw...
₹1,779.00 *
DAC3 click carries Microchip’s MCP4726 IC, a 12-bit digital-to-analog converter, along with voltage output screw terminals. The digital value is converted to the appropriate voltage level in the range between GND and REFERENCE (VCC or...
₹1,889.00 *
ADC3 click carries Microchip’s MCP3428 16-bit multichannel analog-to-digital converter. The click has four pairs of screw terminals onboard, letting you access the chip’s four differential input channels. At the highest resolution of...
₹2,309.00 *
Comparator Click, carrying the LM2903 IC, has two independent precision voltage comparators. Two pairs of screw terminals allow you to connect separate inputs (additional two screw terminals are for GND connections). You can use it...
₹1,259.00 *
V to Hz 2 click DAC Click MUX click ADC2 click ADC click ADC 5 click Analog Key MUX 3 Click DAC 4 Click ADC 4 click DigiVref Click PWR Meter 2 Comparator DIGI POT 2 DIGI POT 4 PWR Meter click Hz to V click RMS to DC click DIGI POT 3 Waveform Click MUX 2 click DIGI POT click ADAC click Voltmeter click DAC 3 Click L meter click PIXI click ADC3 click POT 2 Click C Meter click ADC 6 click PAC1934 click POT Click DAC 5 Click EEG click PAC1921 click Slider 2 Click LEM click POT 3 Click DIGI POT 5 LED Driver 4 Multimeter ADC 8 Click V to Hz click AC Current ADC 7 click
Viewed