Top seller
No results were found for the filter!
USB UART 2 Click USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
₹4,099.00 *
SPI Isolator click SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
₹3,049.00 *
ATA663211 click The click communicates with the target MCU through the UART interface and runs on a 3.3V power supply. ATA663211 click can aslo be used as a standalone LIN transceiver, without being connected to a mikroBUS™ socket. An onboard LDO...
₹1,999.00 *
MCP2542 click MCP2542 is designed specifically for high-speed CAN FD applications with communication speeds of up to 8 Mbps. Longer than usual BUS lengths are supported thanks to the improved maximum propagation delay. The board has a standard RS232...
₹2,099.00 *
MCP2003B click MCP2003B click is a mikroBUS™ add-on board with a bi-directional LIN transceiver . It’s a physical interface to automotive and industrial LIN systems, in accordance to the LIN Bus Specifications Revision 2.2, SAE J2602 and ISO 17987....
₹1,889.00 *
MCP25625 click Named after the main chip, MCP25625 click also has a RS232 port, which is a standard connector for CAN communications. Additionally, the two CAN wires (CANL and CANH) can also be connected directly through two pins on the right edge of...
₹2,519.00 *
USB I2C click USB I2C click carries an MCP2221 USB-to-UART/I2C converter. The chip supports full-speed USB (12 Mb/s), I2C with up to 400 kHz clock rates and UART baud rates between 300 and 115200. The board communicates with the target MCU through...
₹1,459.00 *
Expand 4 click Expand 4 click carries TPCIC6A595 , a chip that combines an 8-bit serial-in, parallel-out shift register with an 8-bit D-type storage register. It’s intended for use as a port expander for connecting high power peripherals. On the output...
₹1,569.00 *
PWM click PWM click is a simple solution for controlling 16 PWM outputs through a single I2C interface. You can use it to control anything from a simple LED strip to a complex robot with a multitude of moving parts. The click board carries the...
₹1,569.00 *
I2C 1-Wire click Description I2C 1-Wire click carries DS2482-800 , a “bridge device” that performs bidirectional conversions between I2C masters and 1-Wire slave devices. These can be EEPROM chips, temperature sensors and similar devices that have...
₹2,939.00 *
Expand 3 click Description EXPAND 3 click carries DS2408 , an 8-channel programmable I/O expander that communicates with the target board MCU through a standard Dallas Semiconductor 1-Wire interface (15.3 kbps or 100kbps). The chip also has a...
₹2,099.00 *
I2C Isolator Click Description I2C Isolator click carries ISO1540 , a low-power, bidirectional isolator compatible with I2C interfaces. On the board, the Texas Instruments chip is connected to two sets of I2C pins, one on the mikroBUS connector (SDA, SCL),...
₹1,889.00 *
UART 1-Wire RS232 2 click ATA6563 click LLC SPI Click Arduino MEGA DALI 2 click RS485 click 5V OBDII click CAN SPI click PI2 click LLC-I2C Click iButton click MCP2518FD click Click UART I2C SPI Fiber Opt click STM32F4 MCP2517FD click I2C 1-Wire GNSS 10 Click Intel Joule Pi 4 Click PS 2 click Pi click shield DALI Click mikroBUS USB I2C click USB UART 3 ETH Click Expand 4 click PWM 2 click FTDI click ETH WIZ click USB SPI click Arduino MKR BroadR-Reach 4-20 mA T click RS485 3 click SPI Isolator LED Driver 13 1-Wire I2C CAN Isolator Arduino UNO RS232 click RS485 4 Click PWM click
Viewed