ATA6563 click

₹2,099.00 *

Prices incl. VAT plus shipping costs

Ready to ship today,
Delivery time appr. 1-3 workdays

Order number: MIKROE-2334
Manufacturer product ID: MIKROE-2334

ATA6563 click carries the ATA6563 high-speed CAN transceiver.... more

Close menu

Product information "ATA6563 click"

ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART interface, with additional functionality provided by the AN pin on the mikroBUS™ line.

ATA6563 features

The ATA6563 is a high-speed CAN transceiver that provides an interface between a controller area network (CAN) protocol controller and the physical two-wire CAN bus.

The transceiver is designed for high-speed (up to 5 Mbps) CAN applications in the automotive industry, providing differential transmit and receive capability to (a microcontroller with) a CAN protocol controller. It offers improved electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance.

The transceiver is CAN FD (Flexible data-rate) ready, meaning it has increased data rates in comparison with classic CAN.

How the click works

ATA6563 click is connected to a CAN bus via the DB9 cable, which then communicates with the network.

Specifications

Type	CAN
Applications	Classical CAN and CAN FD networks in Automotive, Industrial, Aerospace, Medical and Consumer applications.
On-board modules	ATA6563 high-speed CAN transceiver from Microchip
Key Features	Optimized for CAN FD at 2 and 5 Mbps operation, maximum propagation delay: 210ns; the chip supports CAN 2.0 and CAN with flexible data rates.
Interface	UART
Input Voltage	3.3V or 5V
Click board size	L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on ATA6563 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
Standby select	STBY	1	AN	PWM	16	NC
	NC	2	RST	INT	15	NC
	NC	3	CS	TX	14	RX	UART data receive
	NC	4	SCK	RX	13	TX	UART data transmit
	NC	5	MISO	SCL	12	NC
	NC	6	MOSI	SDA	11	NC
Power supply	+3.3V	7	3.3V	5V	10	+5V	Power supply
Ground	GND	8	GND	GND	9	GND	Ground

Jumpers and settings

Designator	Name	Default Position	Default Option	Description
JP1	VIO SEL	Left	3V3	VIO Supply Voltage Selection 3V3/5V, left position 3V3, right position 5V
JP2	MODE SEL	Left	ON	Selection of the standby feature; default is always on, right option switches to the STB pin on the mikroBUS™

Additional pins

Name	I/O	Description
CANL	I/O	CAN lines, same as on DB9 connector
CANH	I/O	CAN lines, same as on DB9 connector
TXD	I	UART lines, same as on the mikroBUS™
RXD	O	UART lines, same as on the mikroBUS™

Programming

Code examples for ATA6563 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

A simple example of the ATA6563 library usage. The example waits until 8 bytes are received on the RX and then prints the received data using the other UART module.

01 void main()
02 {
03     int i = 0;
04     system_init();
05     while( 1 ) {
06         if( Button( &GPIOA_IDR , 5, 100, 1 ) ){
07             ata6563_send( TX_DATA, sizeof( TX_DATA ) );
08             TFT_Write_Text( "Data Sent", 50, 100 );
09         }
10         if( ( chk = ata6563_rdy() ) == 8 ){
11             ata6563_read( buf, chk );
12             for( i = 0; i < chk; i++ )
13                  UART1_Write( buf[ i ] );
14         }
15     }
16 }

Downloads

mikroBUS™ Standard specification
ATA6563 datasheet
ATA6563 click schematic
LibStock: ATA6563 click library