Top seller
No results were found for the filter!
PS/2 click PS/2 click is a cost-effective solution for adding keyboard and mouse connectivity to your design. It features a standard 6-pin Mini-DIN PS/2 connector, a mikroBUS™ host socket, and a power indicator LED. PS/2 click communicates with the...
₹949.00 *
Fiber Opt click Fiber Opt click is a compact and easy solution for adding fiber-optic communication to your design. It features IF-D91 fiber-optic photodiode, IF-E97 fiber-optic LED diode as well as two operational amplifiers. Provided plastic optic...
₹3,569.00 *
FTDI click FTDI Click features FT2232H - dual high speed USB 2.0 to UART/I2C/SPI serial interface converter. It includes DA converter and EEPROM as well. The entire USB protocol is handled on the chip (FTDI USB drivers are required), making this...
₹3,049.00 *
4-20 mA R click 4-20mA R Click is an add-on board in mikroBUS form factor which serves as a receiver in a 4-20mA current loop standard. It features INA196 current shunt monitor, MCP3201 12-bit ADC as well as TPS61041 DC/DC boost converter. It receives...
₹2,729.00 *
DALI Click DALI Click is a compact board that provides Digital Addressable Lighting Interface (DALI) to your design. Board features two optocouplers, push button and screw terminals. DALI Click communicates with target board via four mikroBUS™...
₹2,629.00 *
CAN SPI click 3.3V Description CAN SPI click 3.3V is an accessory board in mikroBUS form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features SN65HVD230 can transciever circuit which provides...
₹2,209.00 *
RS485 click 3.3V Description RS485 click 3.3V carries the SN65HVD12 half-duplex, RS-485 transceiver from Texas Instruments. It is designed for balanced data transmission and complies with EIA standards RS-485 and RS-422. The click is designed to run on a...
₹1,889.00 *
ETH Click Description ETH Click is an accessory board in mikroBus™ form factor. It features ENC28J60 , a 28-pin, 10BASE-T stand alone Ethernet Controller with an on-board MAC & PHY, 8K Bytes of Buffer RAM and SPI serial interface. Chip supports...
₹2,519.00 *
EXPAND click Description EXPAND Click is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23S17 with SPI clock speeds up to 10 MHz for higher throughput applications. Three HARDWARE ADDRESS SEL jumpers allow you to...
₹1,259.00 *
4-20 mA T click 4-20mA T Click is an add-on board in mikroBUS form factor. It’s a compact and easy solution for adding 4-to-20mA industry standard communication protocol to your design. It features ADuM1411 Quad-chanel digital isolator, MCP4921 12-bit...
₹2,729.00 *
USB SPI click USB SPI Click is an accessory board in mikroBUS form factor. It’s a compact and easy solution for adding SPI serial communication via USB cable. It features MCP2210 USB-to-SPI protocol converter with GPIO as well as USB MINI B connector....
₹1,459.00 *
RS485 click 5V Description RS485 click 5V carries the ADM485 differential line transceiver from Analog Devices. It is designed for balanced data transmission and complies with EIA standards RS-485 and RS-422. The click is designed to run on a 5V power...
₹1,889.00 *
I2C Isolator 2 I2C 1-Wire USB UART 3 1-Wire I2C 4-20 mA R click ATA6570 click Expand 3 click LLC SPI Click OBDII click MCP2518FD click Expand 2 click USB UART 4 RS232 SPI click RS485 3 click iButton click Dual LIN click SPI Isolator RS485 click LIN Click FTDI click Terminal click 4-20 mA T click Expand 4 click RS232 click CAN FD Click Shuttle click PWM click ATA663254 click ETH Click Fiber Opt click USB I2C click CAN Isolator M-Bus Master MCP2517FD click RiBUS Click BroadR-Reach USB SPI click CAN SPI click DALI Click CAN SPI click RS485 2 click RS485 Isolator RS485 click 5V LLC-I2C Click EXPAND click USB UART 2
Viewed