Top seller
No results were found for the filter!
MCP2542 click MCP2542 is designed specifically for high-speed CAN FD applications with communication speeds of up to 8 Mbps. Longer than usual BUS lengths are supported thanks to the improved maximum propagation delay. The board has a standard RS232...
₹2,099.00 *
MCP2003B click MCP2003B click is a mikroBUS™ add-on board with a bi-directional LIN transceiver . It’s a physical interface to automotive and industrial LIN systems, in accordance to the LIN Bus Specifications Revision 2.2, SAE J2602 and ISO 17987....
₹1,889.00 *
MCP25625 click Named after the main chip, MCP25625 click also has a RS232 port, which is a standard connector for CAN communications. Additionally, the two CAN wires (CANL and CANH) can also be connected directly through two pins on the right edge of...
₹2,519.00 *
USB I2C click USB I2C click carries an MCP2221 USB-to-UART/I2C converter. The chip supports full-speed USB (12 Mb/s), I2C with up to 400 kHz clock rates and UART baud rates between 300 and 115200. The board communicates with the target MCU through...
₹1,459.00 *
Expand 4 click Expand 4 click carries TPCIC6A595 , a chip that combines an 8-bit serial-in, parallel-out shift register with an 8-bit D-type storage register. It’s intended for use as a port expander for connecting high power peripherals. On the output...
₹1,569.00 *
PWM click PWM click is a simple solution for controlling 16 PWM outputs through a single I2C interface. You can use it to control anything from a simple LED strip to a complex robot with a multitude of moving parts. The click board carries the...
₹1,569.00 *
I2C 1-Wire click Description I2C 1-Wire click carries DS2482-800 , a “bridge device” that performs bidirectional conversions between I2C masters and 1-Wire slave devices. These can be EEPROM chips, temperature sensors and similar devices that have...
₹2,939.00 *
Expand 3 click Description EXPAND 3 click carries DS2408 , an 8-channel programmable I/O expander that communicates with the target board MCU through a standard Dallas Semiconductor 1-Wire interface (15.3 kbps or 100kbps). The chip also has a...
₹2,099.00 *
I2C Isolator Click Description I2C Isolator click carries ISO1540 , a low-power, bidirectional isolator compatible with I2C interfaces. On the board, the Texas Instruments chip is connected to two sets of I2C pins, one on the mikroBUS connector (SDA, SCL),...
₹1,889.00 *
ETH WIZ click Description ETH Wiz click carries W5500 , a 48-pin, 10/100 BASE-TX standalone ethernet controller with a hardwired TCP/IP Internet protocol offload engine, along with a standard RJ-45 connector. The W5500 module employs a variety of...
₹1,999.00 *
Expand 2 click Description EXPAND 2 click is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23017 with I²C clock speeds up to 10 MHz for higher throughput applications. Three HARDWARE ADDRESS SEL jumpers allow you to...
₹1,259.00 *
RS232 click RS232 click is a simple solution for adding RS232 connectivity to your design. RS232 is a serial communications standard mostly used for industrial machines, networking equipment and scientific instruments, as well as for computer...
₹1,579.00 *
PWM 2 click USB I2C click RS232 2 click RS232 click UART I2C SPI Expand 4 click iButton click MCP2003B click RS232 SPI click ETH Click I2C 1-Wire RS485 4 Click ATA6570 click MCP2518FD click Expand 3 click BroadR-Reach LLC-I2C Click RS485 2 click ATA663254 click OBDII click 4-20 mA T click CAN SPI click USB UART click 4-20 mA R click Shuttle click CAN Isolator MCP2542 click I2C Isolator CAN FD Click USB UART 2 SPI Isolator DALI Click MCP2517FD click RS485 Isolator USB UART 3 ATA663211 click Dual LIN click ATA6563 click UART 1-Wire RS232 Isolator 1-Wire I2C DALI 2 click RS485 3 click CAN SPI click PWM click RS485 click 5V
Viewed