Top seller
No results were found for the filter!
Ammeter click Two onboard screw terminals (probe+ and probe-) are bringing in the current, which then passes through a shunt resistor. A voltage proportional to the strength of the current is generated accross the resistor. This voltage passes through...
₹2,519.00 *
C Meter click The chip is implemented in an astable multivibrator circuit with fixed resistors and adjustable capacitors. The board has four different-sized plates for placing SMD capacitors (covering standard SMD packaging dimensions) as well as a...
₹949.00 *
DIGI POT 2 click DIGI POT 2 click is a mikroBUS™ add-on board with a single channel digital potentiometer TPL0501 with 256 wiper positions. The IC has 100 kilo Ohms end-to-end resistance, with ±20% tolerance. The board features two pairs of screw...
₹1,779.00 *
DAC 3 Click DAC3 click carries Microchip’s MCP4726 IC, a 12-bit digital-to-analog converter, along with voltage output screw terminals. The digital value is converted to the appropriate voltage level in the range between GND and REFERENCE (VCC or...
₹1,889.00 *
ADC3 click ADC3 click carries Microchip’s MCP3428 16-bit multichannel analog-to-digital converter. The click has four pairs of screw terminals onboard, letting you access the chip’s four differential input channels. At the highest resolution of...
₹2,309.00 *
Comparator click Comparator Click, carrying the LM2903 IC, has two independent precision voltage comparators. Two pairs of screw terminals allow you to connect separate inputs (additional two screw terminals are for GND connections). You can use it...
₹1,259.00 *
ADC2 click ADC 2 click carries MCP3551/3 , which is a 22-bit ADC with automatic internal offset and gain calibration. This high precision analog-to-digital converter has total unadjusted error of less than 10 ppm, and low-output noise of 2.5 µV...
₹2,519.00 *
DAC Click DAC Click is an accessory board in mikroBUS form factor. It includes a 12-bit Digital-to-Analog Converter MCP4921 that features an optional 2x buffered output and SPI interface. The board provides high accuracy and low noise performance...
₹1,889.00 *
DIGI POT click DIGIPOT Click is an accessory board in mikroBUS form factor. It features a single-channel digital potentiometer MCP4161 with 8-bit resolution (256 wiper steps) and industry-standard SPI serial interface. The resistance value of the...
₹1,779.00 *
ADC click ADC click carries the MCP3204 12-bit Analog-to-Digital converter. The click is designed to run on 3.3V by default. Place PWR SEL SMD jumper to 5V position if used with 5V systems. It communicates with the target microcontroller over SPI...
₹2,519.00 *
ADC 5 click ADC 5 click is a device used to sample an analog voltage on the input and convert it to a digital information. In general, ADC (analog to digital converters) are the most commonly used devices for converting the voltage signals into an...
₹1,889.00 *
PIXI™ click PIXI™ click is equipped with MAX11300 IC from Maxim Integrated , which features Maxim Integrated's versatile, proprietary PIXI ™ technology - it is the industry's first configurable 20-channel mixed-signal data converter. Besides the...
₹3,049.00 *
MOTION click BarGraph 3 Vibro Motor RS485 4 Click RS232 SPI click DHT22 2 click NANO GPS click LTE IoT 2 Click 13DOF Click Balancer 3 DALI 2 click IR Sense 2 UART I2C SPI iButton click USB I2C click 4G LTE-APJ 6LoWPAN C click IrDA 3 click Fiber Opt click 6DOF IMU click RS232 click 3D Hall 6 Click DALI Click Angle 4 click Counter Click M-Bus Master ETH Click LED Driver 3 Tamper 2 click OBDII click GPS Click WiFi2 click I2C to SPi 6LoWPAN T click Hall Current 4 USB SPI click Keylock 2 Click Mikromedia 4 Arduino MKR Pedometer 3 SpeakUp click PS 2 click Heart Rate 7 DC MOTOR 3 3G-AA Click FTDI click
Viewed