EnOcean click

₹4,099.00 *

Prices incl. VAT plus shipping costs

Ready to ship today,
Delivery time appr. 1-3 workdays

  • MIKROE-1908
  • MIKROE-1908
  EnOcean click  carries a  TCM 310  transceiver, which is a... more
Product information "EnOcean click"

 

EnOcean click carries a TCM 310 transceiver, which is a bidirectional gateway for EnOcean’s 868 MHz radio systems. The click is designed to run on a 3.3V power supply. It communicates with the target MCU through UART (TX, RX pins), with additional functionality provided by RST and EN pins.

Note: Modules with 868 MHz frequency are suitable for Europe and other countries adopting R&TTE specification. Versions of EnOcean click covering different frequency bands will be available in the future.

TCM 310 transceiver

This low-powered wireless module is intended for use together with EnOcean’s range of energy harvesting modules that include self-powered, battery-free wireless switches, sensors and actuators.

Essential features

EnOcean offers a range of modules compatible with TCM 310. Those are miniaturized energy converters that use the surrounding environment — motion, light or temperature differences — to harness enough energy to send a wireless signal to the receiver onboard EnOcean click.

The TCM 310 module can also be set up as a repeater to extend the range of the signal. You can then develop various battery-free switching systems, data loggers and similar.

Onboard antenna

EnOcean click features a small high-performance 868MHz chip antenna onboard so no external antennas are required.

Key features

  • TCM 310 transceiver
    • Frequency: 868 MHz EnOcean
    • Data rate: 125 kbps
  • Onboard antenna
  • Interface: UART
  • 3.3V power supply

Specification

Type RF Sub 1GHz
Applications Incorporate battery-free wireless energy harvesting modules into your designs
On-board modules TCM310 transceiver
Key Features Bidirectional gateway for EnOcean 868 MHz radio systems. Compatible with EnOcean energy harvesting modules
Key Benefits Communicates with battery-free switches, sensors and actuators. Onboard chip antenna
Interface GPIO,UART
Input Voltage 3.3V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on EnOcean click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.png

mikroBUStm

PinNotes
Not connected NC 1 AN PWM 16 EN In read mode, the firmware version and configuration area can be read from the module
Reset input RST 2 RST INT 15 NC Not connected
Not connected NC 3 CS TX 14 SER_TX UART output
Not connected NC 4 SCK RX 13 SER_RX UART input
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Power supply +3.3V 7 3.3V 5V 10 NC Not connected
Ground GND 8 GND GND 9 GND Ground

Programming

The function sends ESP3 packet header and data over UART interface to an EnOcean module.

01 uint8_t sendMessage(ESP3Pack* esp){
02
03   uint8_t i=0;
04
05   if((esp->header.dataLength || esp->header.oppDataLength) == 0)
06    {
07      return -1;
08     }
09
10   UART2_Write(esp->syncByte);
11   UART2_Write((esp->header.dataLength & 0xFF00)>>8);
12   UART2_Write((esp->header.dataLength & 0xFF));
13   UART2_Write(esp->header.oppDataLength);
14   UART2_Write(esp->header.packetType);
15   UART2_Write(esp->headerCRC);
16
17   for(i=0; i < esp->header.dataLength; i++)
18       UART2_Write(esp->dataESP3[i]);
19   for(i=0; i < esp->header.oppDataLength; i++)
20       UART2_Write(esp->optData[i]);
21
22    UART2_Write(esp->dataCRC);
23
24    return 0;
25 }

Related links to "EnOcean click"
Read, write and discuss reviews... more
Customer evaluation for "EnOcean click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

Viewed