Top seller
No results were found for the filter!
RS485 3 click RS485 3 click uses SN65HVD31DR from Texas Instruments , a tri-state differential line driver and differential input line receiver. The click is intended to be used as UART to RS422/RS485 communication interface. It is suited for...
₹2,099.00 *
USB UART 4 click USB UART 4 click features well-known FT232RL USB-to-UART interface module from FDTI . It provides USB to asynchronous serial data transfer interface, allowing the microcontroller based designs to communicate with the personal computer,...
₹1,459.00 *
MCP2517FD click MCP2517FD click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector. The click requires both 3.3V and 5V power supply. It...
₹2,629.00 *
1-Wire I2C click 1-Wire I2C click carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply. It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™...
₹2,309.00 *
RS485 Isolator click RS485 Isolator click is a RS485 communication isolator, and carries the ADM2682EBRIZ , a 5 kV rms signal and power isolated RS-485 transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the...
₹5,149.00 *
CAN Isolator click CAN Isolator click provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter. The click is designed to run on either 3.3V or 5V power supply. CAN...
₹4,099.00 *
ATA6563 click ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART...
₹2,099.00 *
RS485 2 click RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller...
₹1,889.00 *
I2C Isolator 2 click I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The...
₹2,519.00 *
USB UART 2 Click USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
₹4,099.00 *
SPI Isolator click SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
₹3,049.00 *
ATA663211 click The click communicates with the target MCU through the UART interface and runs on a 3.3V power supply. ATA663211 click can aslo be used as a standalone LIN transceiver, without being connected to a mikroBUS™ socket. An onboard LDO...
₹1,999.00 *
CAN SPI click USB UART 3 LLC-I2C Click NFC click RS485 2 click Heart rate 6 ETH Click BarGraph 2 Fiber Opt click Secure 3 click EERAM 3.3V Accel 7 click AC Current iButton click DALI 2 click RS232 Isolator LLC SPI Click CAN Isolator RS232 click BroadR-Reach Light Temp mikroC PRO for USB I2C click ATA6570 click UPS click mikroPascal PRO UART 1-Wire UART I2C SPI WiFi 5 click EasyPIC Fusion 4-20 mA R click Ready for XMEGA mikroC PRO for MikroBasic PRO I2C Isolator 2 RS485 4 Click RS485 3 click EasyLV-18F v6 Voltmeter click CAN SPI click RS485 click 5V RS232 2 click ATA663254 click 1-Wire I2C mikroC PRO for PWM click
Viewed