Top seller
No results were found for the filter!
ADC 8 Click ADS1115 can operate either in continuous or in a single-shot mode. While operating in a single-shot mode, the current consumption is significantly reduced, since the ADS1115 powers down after each conversion. Its maximum sample rate in...
₹2,209.00 *
Brushless 3 click Brushless 3 click carries the DRV10983 , a three-phase sensorless motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brushless DC motor through the PWM pin, AN pin or I2C interface. It...
₹1,999.00 *
Brushless 2 click Brushless 2 click carries the DRV10964 BLDC motor controller with an integrated output stage from Texas Instruments. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the...
₹1,789.00 *
Stepper 4 click Stepper 4 click carries the TB67S269FTG , a two-phase bipolar stepping motor driver from Toshiba. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the following pins on...
₹1,999.00 *
Fan 2 click Fan 2 click carries the MAX31760 precision fan-speed controller. It can measure temperature and adjust the fan speed to keep the temperature at the same level. Fan 2 click can also control two fans at the same time. The click is designed...
₹1,579.00 *
DC MOTOR 5 click DC MOTOR 5 click carries the DRV8701 brushed DC motor gate driver from Texas Instruments. The click is designed to run on an external power supply. It communicates with the target MCU over the following pins on the mikroBUS™ line: AN,...
₹1,789.00 *
DC MOTOR 4 click DC MOTOR 4 click is capable of driving motors with a supply voltage from 4.5V to 36V . It carries the MAX14870 motor driver from Maxim Integrated. The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click...
₹1,579.00 *
PWM driver click If you need to control DC motors with loads up to 10A, PWM driver click is the perfect solution, thanks to the Silicon Lab Si8711CC one-channel isolator. It communicates with the target MCU over PWM pin, and runs on a 5V power supply. It...
₹1,469.00 *
DC MOTOR 3 Click Two pairs of screw terminals are positioned on the top of the board. One is for bringing an external power supply; the other is for connecting a motor. TB6549FG has four operating modes: clockwise, counter-clockwise, short brake and...
₹1,999.00 *
Stepper 3 click The board carries a Texas Instruments ULN2003 High-Current Darlington transistor array for operating the motors. Motors are connected through a 4-pin male connector on the top of the PCB. They can be driven by the click board's own power...
₹1,999.00 *
Stepper 2 click Stepper 2 click is a complete solution for driving bipolar stepper motors with full/half and micro-steps. It features the A4988 IC from Allegro Microsystems with DMOS low RDSONÂ drivers on its outputs, which ensure high efficiency and...
₹1,999.00 *
HAPTIC click Haptic click carries DRV2605 , a Haptic Driver for ERM and LRA vibration motors (acronyms stand for Eccentric Rotating Mass and Linear Resonant Actuator, respectively). The DRV2605 IC integrates an extensive library with over 100 haptic...
₹2,419.00 *
Voltmeter click RS232 click EasyPIC Fusion ATA663254 click iButton click Ready for XMEGA ETH Click RS485 2 click RS485 4 Click mikroC PRO for EERAM 3.3V UART I2C SPI EasyLV-18F v6 WiFi 5 click LLC SPI Click 1-Wire I2C LLC-I2C Click Light Temp I2C Isolator MikroBasic PRO Accel 7 click BarGraph 2 USB I2C click Brushless 3 RS232 Isolator ATA6570 click CAN Isolator UPS click RS485 3 click mikroC PRO for Heart rate 6 USB UART 3 UART 1-Wire I2C Isolator 2 NFC click AC Current DALI 2 click RS485 click 5V CAN SPI click CAN SPI click Secure 3 click 4-20 mA R click V to Hz 2 click RS232 2 click mikroC PRO for mikroPascal PRO
Viewed