Top seller
No results were found for the filter!
Battery Holder (4 x AA) Features: Holds four AA cells Header connector for easy connection to many Digilent boards Polycarbonate construction
₹319.00 *
Hirose FX2 Socket Connector This 100-pin socket allows users to build their own boards that interface with the Hirose FX2 expansion connector included on several of our system boards, including the Nexys, Nexys 2, Virtex ® -II Pro, and Spartan ® -3E Starter Board....
₹1,719.00 *
5V 2.5A Switching Power Supply Features: 5V, 2.5A Switching Power Supply Suitable for use with the Zybo™ FPGA board Can also be used as an external power supply for the Analog Discovery 2
₹1,529.00 *
European Wall Plug Adapter Features: Convenient way to switch from US wall plug to European or UK wall plugs Simple snap-on design Used with Digilent's switching power supplies US to European wall plug adapter
₹339.00 *
UK Wall Plug Adapter Features: Convenient way to switch from US wall plug to European or UK wall plugs Simple snap-on design Used with Digilent's switching power supplies US to UK wall plug adapter
₹399.00 *
Digilent Screwdriver This remarkable and stylish tool is sure to become the centerpiece of any dedicated techie's tool box! Our screwdriver features standard and Phillips bits as well as a pocket clip for on-the-go convenience. Not only is the Digilent...
₹399.00 *
Solderless Breadboard Kit: Large Features Large breadboard with rugged steel backing 3x 630 tie point terminal strips included 5x 100 tie point distribution strips included Four screw terminals for power supply connections included 4 adhesive rubber feet included
₹6,589.00 *
WS2812 Addressable LED: 1M Waterproof Strip Educators, need to add a little excitement to your lab exercises? These LED strips are just about the best way to get tons of colorful LED light with a minimum of wiring and fuss! Each strip is one meter in length and contains 30 light...
₹2,449.00 *
Heatsink with Clip This heatsink is a great way to ensure that none of your chips overheat, and with its convenient clip and adhesive backing, installation and removal is a breeze. The clip will fit perfectly on the Virtex-5 board, or any chip measuring...
₹1,839.00 *
Wire Wrap or Protoboard Expansion for NI myRIO The MXP Wire Wrap provides a large 14x21 hole prototyping area on an expansion card compatible with the myRIO Expansion Port (MXP). The MXP Wirewrap functions as an I/O breakout, with bus traces for GND, 3.3V, and 5V on either side of...
₹1,149.00 *
MXP Extender Cable for myRIO This cable is designed to extend reach of the myRIO expansion port (MXP). The MXP extender cable is perfectly suited for mounting expansion boards, such as the Pmod Adapter. Features: 34-pin male and female connectors 8" length (210±10mm)
₹569.00 *
myDigital Protoboard for NI myDAQ & myRIO The Digilent myDigital accessory board for the NI myDAQ and NI myRIO is designed to provide students a cost-effective, portable, and engaging platform for teaching electronics. With a myDAQ / myRIO, NI Multisim, and a myDigital, you'll...
₹11,099.00 *
60W PCIe 12V 5A 9 2-pin MTE High Speed Screw Terminal Ultimate Analog Analog IR Proximity DMM Shield UK Wall Plug Heatsink with 30-Pin Flywire myProto DMM Probes Ettus USRP N210 High Current 18 2-pin MTE 2x6 Pin Header HDMI Cable Type Blank Canvas IR Range Sensor Breadboard Breadboard Analog 5V 2.5A Breadboard Analog NI Multisim Half-Size 3.3V PowerBRICK Digital Impedance FX2 Module Solderless Enclosure Kit USB A to Mini-B DC Motor - 150 9V PowerBRICK 5V 4A Switching Embedded Vision 40-pin DIP Analog Analog myDigital Coax Power Digilent Digital
Viewed