Top seller
No results were found for the filter!
SparkFun Analog MEMS Microphone Breakout -... The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into...
₹769.00 *
SparkFun RFID Qwiic Kit The SparkFun RFID Qwiic Kit is a simple, yet all-in-one I 2 C based RFID starting point for the ID-3LA, ID-12LA, and ID-20LA readers. Simply plug a reader into the headers and use a Qwiic cable to connect to any Qwiic enabled development...
₹4,939.00 *
Tsunami Super WAV Trigger (Qwiic) Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop and stop independently,...
₹9,449.00 *
MyoWare 2.0 Arduino Shield The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack...
₹1,599.00 *
MyoWare 2.0 Cable Shield The MyoWare® 2.0 Muscle Sensor is designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the board; this is...
₹899.00 *
MyoWare 2.0 LED Shield The MyoWare® 2.0 LED Shield is designed to display the magnitude of a target muscle's signal and power the MyoWare 2.0 Muscle Sensor with its built-in battery. The blue 10-segment bar graph shows the magnitude of the measured signal. The...
₹3,999.00 *
MyoWare 2.0 Link Shield The MyoWare® 2.0 Link Shield is designed to easily connect a MyoWare 2.0 Muscle Sensor to your Arduino microcontroller. The shield provides a 3.5mm TRS jack so that you can use a 3.5mm TRS-to-TRS cable to link the boards together. The...
₹1,999.00 *
MyoWare 2.0 Muscle Sensor Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what if we could take the buttons, levers and joysticks out of the equation and control it...
₹4,599.00 *
MyoWare 2.0 Power Shield The MyoWare® 2.0 Power Shield is designed to easily power the MyoWare 2.0 Muscle Sensor for remote applications. The MyoWare Power Shield is equipped with snap connectors on the board so you can easily stack it to the top side of the...
₹2,199.00 *
MyoWare 2.0 Reference Cable The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready,...
₹189.00 *
SparkFun Analog MEMS Microphone Breakout -... Description : The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to...
₹769.00 *
Telescopic Antenna SMA - 75 MHz to 1 GHz (ANT500) Description : This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male...
₹3,059.00 *
Makey Makey SparkFun Qwiic Garmin SparkFun LoRa SparkFun Block Magnetic Card Magnetic Door Copper Tape - Electric Hobby SparkFun Pulse SparkFun Block SparkFun GNSS L1 L5 S-Video Cable - Concave Button Slide Pot - Slide Pot - SparkFun Load SparkFun RGB 7-Segment Micro Gearmotor LED - 5mm Pocket Geiger Spring Sparkfun MyoWare 2.0 LED JST SH Jumper 4 Li-Ion Polymer SparkFun Teensy 4.0 ProtoSnap - Flexinol - Header - 8-pin Triple Output Slide Pot - Solder Tip HackRF One from Coin Acceptor - SparkFun USB SST Liquid Stackable RFID Tag - 5-Pin Chassis Big Dome Push RTL-SDR BLOG V3 LED String
Viewed